|
|
| You Are Here: Home -> Signal Generators -> RF Signal Generator -> Anritsu MG3633A's details |
|
Anritsu MG3633AAnritsu MG3633A --- 0.01-2700MHz SYNTHESZED SIGNAL GENERATOR
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Carrier frequency | Range | 10 kHz to 2700MHz | ||
| Resolution | 0.01Hz | |||
| Accuracy | Same as that of the reference oscillator | |||
| Internal reference oscillator*^1 | Frequency:10MHz Start-up characteristics:After 30 minutes of operation:≒1*10^-7/day, after 60 minutes of operation: ≒5*10^-8/day, Aging rate :After 24 hours of operationL≒2*10^-8/day, Temperature characteristics: ㊣5*10^-8/day (0∼ to 50⊥) | |||
| External reference signal input | 10MHz,TTL Level,BNC connector on rear panel | |||
| Reference signal output | 10MHz,TTL Level,BNC connector on rear panel | |||
| Switching time | ≒10ms (time form last command until frequencyhas stabilized to within ㊣500Hz of set frequency,during remote operation) | |||
| Output | Range | -143 to +23dB | ||
| Units | dBm,dB米V,V,mV,米V,(Terminated and open voltages are selectable for dB米V,V,mV,or 米V) | |||
| Resloution | 0.1dB | |||
| Frequency response | ㊣0.5dB referred to 0 dBm (<1280MHz),㊣1dBreferred to 0 dBm(≡1280MHz) | |||
| Accuracy | Output level\ Frequency |
10kHz to <1280MHz | ≡1280MHz | |
| +1701 to +23dBm |
- | - | ||
| +15.1 to +17dBm |
㊣1dB | - | ||
| -122.9 to +15dBm |
㊣1dB | ㊣2dB | ||
| -132.9 to -123 dBm |
㊣3dB | ㊣4dB | ||
| -143 to -133dBm |
- | - | ||
| Impedance | 50次,N-type connector VSWR:≒1.5(<1280MHz,≒-3dBm)≒1.8(≡1280MHz≒-3dBm) | |||
| Switching time | Time form last command until output levelis stabillzed ,during remote operation:≒25ms(at LEVEL NORMAL mode) ≒5ms (at LEVEL CONTINUOUS mode) | |||
| Interference radiation | ≒1米V(Value is voltage terminated with 50次load ,measured 25 mm form oront panel with a two-turn 25mm diameter loopantenna )Except sweep mode | |||
| Signal purity | Spurious | At+7dBm CW mode:(fc: carrier frequency) | ||
| Harmonics(2nd,3rd):≒-30dBc(at ≡100kHz) Sub-harmonics(fc/2,3fc/2,5fc/2):None(at <1280MHz)≒-30dBc(at ≡1280MHz) Non-harmonics: ≒-80dBc(fc <640MHz;≡10kHz offset) ≒-74dBc(640MHz≒fc<1280MHz≡10kHz forrst ≒-68dBc(fc ≡1280MHz,≡10kHz offset) | ||||
| SSB phase noise | At+7dBm,CW mode,0∼ to 35⊥ | |||
| Offset frequency |
1kHz | 20 to 300kHz | ||
| 0.01 to <40 MHz |
-116dBc/Hz | -140dBc/Hz | ||
| 40 to <300MHz |
-119dBc/Hz | -145dBc/Hz | ||
| 300 to <600MHz |
-113dBc/Hz | -143dBc/Hz | ||
| 600 to <1100MHz |
-107dBc/Hz | -140dBc/Hz | ||
| 1.1 to <2.4GHz |
-101dBc/Hz | -132dBc/Hz | ||
| 2.4 to <237GHz |
-97dBc/Hz | -120dBc/Hz | ||
| Floor noise:≒145 dBc/Hz(40 to <110MHz) | ||||
| Residual AM | ≒0.02% rms at ≡150kHz(demodulation band:300Hzto 3kHz) | |||
| Residual FM | ≒0.8Hz rms at <1280MHz(demdulation band:300Hz to 3kHz) ≒4Hz rms at <1280MHz(demdulation band :300Hz to 3kHz) | |||
| Ampli- tude modul- ation |
Range | 0 to 100% | ||
| Resolution | 01% | |||
| Internal modulation frequency | Fixed frequency:400Hz,1kHz Variable frequecny:0.1Hz to 50 kHz ,0.1Hz resolution Frequency accuracy:100 ppm | |||
| Accuracy | ㊣(5% of indicated value+2%)[at ≡250kHz ,≒+7dBm,0 t 90% and internal 1kHz | |||
| At ≒㊣7dBm㊣1dBbandwith | ||||
| Lower modulation frequency limit | 20Hz(EXT AC mode),DC(EXT DC mode) | |||
| Upper modulation frequency limit | Carrier frequecny\ Modulation factor |
0 to 30% | 30.1 to 80% | |
| 0.25 MHz ≒fc<0.5MHz | 5kHz | 5kHz | ||
| 0.5 MHz ≒fc<80MHz |
20kHz | 10kHz | ||
| 80MHz≒fc | 50kHz | 20kHz | ||
| External modulation | Input level:Approx.2 Vp-p 600次 Input Impedance:Nominal 600次 | |||
| Depth | ≒1%(at≡1MHz≒+7dBm internal 1kHz 30%z) ≒3%(at≡1MHz≒+7dBm internal 1kHz 80%) ≒ 3%(at 250kHz≒fc<1MHz ≒+7dBm internal 1kHz 30%) ≒10%( at 250kHz≒fc<1MHz ≒+7dBm internal 1kHz 100%) | |||
| Incidental FM | ≒200Hz peak(at ≒250kHz+7dBm internal 1kHz30%) | |||
| Fre- quency modu- lation |
Range | 0 to 400kHz(1MHz ≒fc<40MHz) 0 to 100kHz(40MHz ≒fc<80MHz) 0 to 200kHz(80MHz ≒fc<160MHz) 0 to 400kHz(160MHz ≒fc<320MHz) 0 to 800kHz(320MHz ≒fc<640MHz) 0 to 1.6,MHz(640MHz ≒fc<1280MHz) 0 to 3.2MHz(1280MHz≒fc) | ||
| Resolution | 10Hz (0 to 9.99 kHz deviation) 100Hz (10 to 99.9kHz deviation) 1kHz (100 to 666 kHz deviation) 10kHz (1 to 3.2 MHz deviation) | |||
| Internal modulation frequency | Fixed freqeuncy:400Hz ,1kHz Variable frequency:0.1 to 100kHz 0.1Hz resolution Frequency accuracy:100ppm | |||
| Accuracy | ㊣(5% of indicated valeu+20Hz)[internal 1kHz) | |||
| Modulation frequency response | ㊣1dB bandwidth Frequency range :20Hz to 100kHz(EXT AC mode )DC to 100kHz (EXT DC mode) | |||
| External modulation | Input level :Approx.2 Vp-p/600次 Input impedance:Nominal 600次 | |||
| Distortion | ≒1%(internal 1kHz 3.5kHz deviation) | |||
| Incidental AM | ≒4%(internal 1kHz 22.5 kHz deviation,demodulationband 0.3 to 3kHz) | |||
| Carrier frequency accuracy in DC-FM mode | ㊣500Hz for 30-minute period after calibrationand 2-hour warm-up(at <1280MHz,<10kHz deviation) | |||
| Phase modul- ation |
Range | 0 to 80 rad (1MHz ≒fc<40MHz) 0 to 20 rad (40MHz ≒fc<80MHz) 0 to 40 rad (80MHz ≒fc<160MHz) 0 to 80 rad (160MHz ≒fc<320MHz) 0 to 160 rad (320MHz ≒fc<640MHz) 0 to 320 rad (640MHz ≒fc<1280MHz) 0 to 640 rad (1280MHz ≒fc) Besiees radian,deg unit is also possible for phase deviation display.However,mzs.999deg | ||
| Resolutin | 0.01 rad (0 to 9.99 rad deviation) 0.1 rad (10 to 99.9 rad deviation) 1 rad (100 to 640 rad deviation) | |||
| Internal modulatio frequency | Fixed freqeuncy:400Hz ,1kHz Variable frequency:0.1 Hz to 5kHz 0.1 resolution Frequency accuracy:100ppm | |||
| Accuracy | ㊣(10% of indicated valeu+20Hz)[internal1kHz modulation] | |||
| Modulation frequency response | ㊣1dB bandwidth Frequency range :20Hz to 5kHz(EXT AC mode )DC to 5kHz (EXT DC mode) | |||
| Externulation | Input lievel:Approx.2 Vp-p/600次 Input impedane:Nominal 600次 | |||
| Distortion | ≒(internal 1 kHz 5 rad modulation) | |||
| Intemal modul- ation signal |
Frequency range | 400 Hz ,1kHz,(fixed oscillator) 0.1Hz to 100kHz (variable oscillatior) DC voltage signals equivalent peak values of internal modulationg sine wavecan be applied as a modulationg singnal using the SPECLAL FUNCTION. | ||
| Resolution | 0.1Hz | |||
| Frequency accuracy | 100ppm | |||
| Distion | ≒0.03%(fixed,400Hz and 1kHz)≒0.3%(variable20Hz to 50kHz) | |||
| Memory function | Frequency memory | 1000 carrier frequencies(store /recall) | ||
| Funcition memory | 100 panel settings(store/recal) | |||
| Sweep mode | Carrier freqeuncy ,output level,AF frequency | |||
| Sweep tunc- tion |
Sweep time | 0.1 ms to 600s ,0.01ms resolution(minimumtime depends on the switching time of each function.) | ||
| Other func- tions |
Marker | One movable marker | ||
| Sweep signal output | Staircase (saw-tooth waeform ),Start point:0V,Stop point:100V) | |||
| Modulation signal output | Modulation signal is outputwhen modulationg Output level:Approx.2 Vp-p/600次 | |||
| Relative value display | Carrier frequency,output level | |||
| Continuouly variable output level mode | Continuousltyvariable within a㊣10dB rqngeof the set level Step size:0.1dB | |||
| Trigger function | Previously programmed operation procedurecan be started by a trigger input through its input termibal(on reqr panel,BNCconnector,TTL level)Maximum program steps for triggereed operation:99 steps | |||
| Memory backup | Last settings are stored when pwer is turnedoff | |||
| GPIB | Interfacce function:SH1,AH1,T5,L3,TE0,RL1,PP0,DC1,DT1,CO | |||
| Reverse power | Maxium reverse input power:50W (<100MHz)25W(≡1000MHz)㊣DC50V | |||
| Operating- temperatur |
0 ∼to 50⊥ | |||
| Power | *7Vac+10 -15%48 to 63 Hz ≒270VA | |||
| Dimensions- and mass |
426(W)*177(H)*451(D)mm≒32kg | |||
| EMC*^8 | EN55011:1991,Group 1, Class A EN50882-1:1992 | |||
| Safety | EN61010-1:1993(Instalation Category II PollutionDegree II) | |||
Quality Assurance:Most of our equipment is tested in our staff on-site laboratory prior to shipping. An operational check is performed on all equipment sold to insure that it meets or exceeds the manufacturer's specifications.
We supply all available standard accessories and an operation manual with most pieces of equipment.
Consult your Application Engineer at 86-755-83777077 for details specific to this model.
You may also be interested in these Comparable Instruments![]() |